If your myQ Secure View Floodlight Camera isn't behaving as expected, start with the common issues below. If those don't resolve it, the LED status and reset tables can help you pinpoint what's happening.
Applies To: myQ Secure View Floodlight Camera, model MYQC31FXXW
If the Floodlight Camera will not connect, appears offline, or setup stops, check the status LED first. Find the matching LED under Troubleshoot by LED Status and follow the steps for that light.
If the problem is with power, the floodlight, motion detection, recorded video, or the status light, see Other Floodlight Camera Issues.
Choose the situation that best matches your camera.
If This Is Your First Setup
→ Follow myQ Secure View Floodlight Camera | Install and Setup If setup stops on an LED light, find that light in LED Status Indicators.
If You Changed Your Router or Wi-Fi Password
→ Reconnect the camera in the app. See myQ Device Offline After Wi‑Fi or Router Change | How to Reconnect.
If the Camera Worked Before but Is Now Offline
→ Follow Camera Worked Before but Is Now Offline.
If You Are Giving the Camera to Someone Else
→ Remove the camera from your account, then factory reset it. See myQ App | Remove a Device From Your Account and Factory Reset below.
If the Floodlight Camera was previously online and you did not change your router, Wi-Fi name, or Wi-Fi password, restart your router before continuing with LED troubleshooting.
Other devices in your home may still work normally while the camera is stuck using a connection that the router has not refreshed. Restarting the router refreshes the connection so the camera can try connecting again.
What success looks like: The Floodlight Camera returns online in the myQ app.
If the camera remains offline, check its status LED and continue to Troubleshoot by LED Status.
The status LED shows what the Floodlight Camera is doing during startup, setup, and connection. Each accordion below shows an LED color and what that light means. Find the light currently showing on your camera, open the matching accordion, and follow the steps to fix the issue.
Sometimes restarting your router can fix most connection issues.
Other devices in your home may still work normally while the camera is stuck using a connection that the router has not refreshed. Restarting the router refreshes the connection so the camera can try connecting again.
Wait a moment for the camera to finish powering up. When it is ready to continue, the light changes to flashing blue.
Make sure Bluetooth is turned on and connected on your phone. Continue setup in the myQ app. If setup stopped, keep your phone near the camera, press and hold the reset button (located on the back of the camera, near the top) for 2 seconds, and try again.
If this is your first setup, see Install and Setup.
Confirm your home Wi-Fi is working, then check your router and internet connection.
Restart your router. Once it is back online, allow the camera time to connect to Wi-Fi. If it still does not connect, check your Wi-Fi name and password.
Allow the camera time to connect to myQ. If it stays flashing green, confirm your internet connection is working.
No action is needed if the camera is working normally. If you were previously connected but the camera does not appear on the Home screen, make sure you are signed in to the correct myQ account.
Keep the camera connected to Wi-Fi. The update may take up to 15 minutes.
Wait for the camera to return to its operating range of -4°F to 122°F (-20°C to 50°C).
If the Floodlight Camera worked before but you changed your router, Wi-Fi name, or Wi-Fi password, reconnect it to the updated network.
For more detailed steps, see myQ Device Offline After Wi‑Fi or Router Change | How to Reconnect
Check the current status LED and use Troubleshoot by LED Status to identify where the connection stopped.
Both resets use the reset button on the back of the camera, near the top. Watch the LED closely. Releasing the button at the wrong moment puts the camera into the wrong mode.
| What You See | Light | What It Means |
|---|---|---|
| Solid blue | Release the reset button to enter Set Up mode. | |
| Solid red | Release the reset button to enter Factory Reset mode. |
If your camera can't connect to Wi-Fi and you need to update its network settings, press and hold the reset button until the status LED turns blue, then release. The app will prompt you for your Wi-Fi credentials.
Solid blue light
Use a factory reset if you're giving your Floodlight camera to someone else. Press and hold the reset button until the LED turns blue and then solid red, then release. The camera will enter setup mode as if it were new.
Solid red light
The Bluetooth beacon may have timed out. Press and hold the reset button (located on the back of the camera, near the top) for two (2) seconds, then try again.
Make sure you're connecting to a 2.4 GHz Wi-Fi network. The camera does not support 5 GHz. For router settings, see myQ Cameras | Wi‑Fi Network Requirements and Recommended Router Settings.
Use your phone to confirm Wi-Fi is available at the camera's location. If the signal is weak, move the router closer, then press and hold the reset button for about two (2) seconds and try again.
The device is performing a firmware update over Wi-Fi. Keep it powered on and connected to Wi-Fi. The update can take up to 15 minutes.
Flashing purple light
Then verify the wires are securely connected.
Confirm power is turned on at the circuit breaker or fuse box. If the device is wired through a light switch, confirm the switch is on.
Verify the motion sensor is facing the ground.
Increase motion sensitivity in the app, and make sure the camera's view isn't blocked.
Recorded events require a subscription plan, and Video Recording must be turned on. To turn on Video Recording, see myQ Cameras | Camera Detection Settings Overview.
Check to see if the status LED is turned off in the camera settings. See myQ Secure View Floodlight Camera | Features and Settings.
Check the wiring and mounting screws in myQ Secure View Floodlight Camera | Install and Setup.

Strictly necessary cookies are vital for our website’s core functions, such as security, network management, and accessibility. Since they are essential, these cookies cannot be disabled in our systems.
Third party trackers collect information to use for analytics and to personalize your experience with targeted ads. Under the Colorado CPA, the Virginia CDPA, the Texas DPSA, the Oregon CPA, the Montana CDPA, and the Florida DBR, you have the right to opt-out of the sale of your personal data to third parties, of targeted advertising related processing, and of some types of profiling. You may exercise your rights by using the toggles below. If you opt out, the ads and content that you see may not be as relevant to you. Under the Colorado CPA, you have the right to opt back in to these categories at any time should you initially choose to opt out, and you may do so using the same toggles provided below. For more details on the data we process and how to exercise your rights, and to view information related to required opt-in disclosures, see our Privacy Policy
We and our advertising partners may set these cookies to deliver relevant ads both on our site and across other sites. You can opt-out of these cookies, but you may see less personalized advertising as a result.
These cookies, along with select third-party partners, help us understand how visitors use our site, such as which pages are popular and how long they stay. You can opt-out of these cookies, but your experience may be less customized.