A hand-held remote control should operate anywhere from two to three car lengths away from the garage. This article details troubleshooting steps to possibly locate interference.
NOTE: For models manufactured between 1993-1997, there is no longer an option to switch out the logic board as the board is no longer available.
EV and MAX Remote Controls (manufactured BEFORE 2022)
Evolution remote controls (models end in EV/MAX) manufactured before 2022 are compatible with all Chamberlain models manufactured since 1993. During programming, each press of the button or enter corresponds with a certain code. Each time the button is pressed it cycles to the next code type.
- 1 Press = Yellow Learn Button. 310/315/390MHz Security+ 2.0
- 2 Presses = Purple/Brown Learn Button. 315MHz Security+
- 3 Presses = Red/Orange Learn Button. 390MHz Security+
- 4 Presses = Green Learn Button. 390MHz Billion Code
EVMC and MAXMC Remote Controls (manufactured AFTER 2022)
Evolution remote controls (models ending in EVMC/MAXMC) manufactured after 2022 are compatible with all Chamberlain models manufactured since 1993. During programming, each press of the button or enter corresponds with a certain code. Each time the button is pressed it cycles to the next code type.
- 1 Press = Yellow Learn Button. 315MHz Security+ 2.0
- 2 Presses = Purple/Brown Learn Button. 315MHz Security+
- 3 Presses = Red/Orange Learn Button. 390MHz Security+
- 4 Presses = Green Learn Button. 390MHz Billion Code
If you're not sure of the learn button color see Determine the Color of the Learn Button on Your Garage Door Opener for more information.
myQ Control Panel and Security+ 2.0 Option
If the garage door opener was manufactured in 1998 or newer, we recommend you purchase a myQ Control Panel and Security+ 2.0 remote control.
*The 889LM or 041A7928-3 door control panels have Security+ 2.0 technology, virtually eliminating interference. The Security+ 2.0 technology also allows you to use the myQ app to allow control of your garage door from anywhere.
Compatible Security+ 2.0 options
Door Control
LiftMaster® myQ Control Panel 889LM
Chamberlain Wall Control Panel model 041A7928-3
Remote Controls
LiftMaster® Security+ 2.0 Remotes
Chamberlain Security+ 2.0 Remotes
There are several reasons why an opener would lose range. Click on a specific reason to be taken to that section in this article, or scroll to review all reasons.
Important troubleshooting note: Testing the remote control range after each step is imperative.
Check Physical Interference Basics
Visor
Remove remote control from car visor and test (if permanently stationary).
Battery
If only one remote control is having an issue, replace the old battery with a new battery and test
Antenna
Straighten the antenna wire hanging from the Garage Door Opener and test
Metal Building
All remotes controls are affected, it may have always been an issue. The customer can purchase an
Antenna Extender Kit part # 041A3504 on our website. Test once installed
- Is there still a range issue?
- No, then either the battery or a physical blockage was interfering with the remote.
- Yes, continue to troubleshoot
Check for Radio Frequency Interference (RF Interference)
LED light bulbs
Located outside the garage and in or around the Garage Door Opener, some LED light bulbs generate radio interference.
Note: Some states, such as California, do not allow the use of incandescent bulbs.
See: Light Bulbs That Can Be Used in Garage Door Openers
Bulbs to never use:
- Bulbs that exceed the recommended wattage for your opener.
- Halogen light bulbs
- Short neck or specialty light bulbs
Refer to your product manual for the correct size bulb.
LED Bulb Troubleshooting
- Swap out LED bulbs located from the Garage Door opener with 100watts incandescent, CFL bulbs or just remove LED if a compatible replacement is not available (swapping bulbs will not leave the light socket open for additional interference issues
- Test remote. Is there still a range issue?
- No, then you're done, the LED bulbs, in the opener, were causing the issues**
- Yes, continue troubleshooting
- Now disconnect other LED bulb sources located around the Garage Door Opener from power.
- Test remotes control. Is there still a range issue?
- No, the surrounding LED is causing the issue. Replace the LED lights with a different brand or a different type of bulb.**
- Yes, continue troubleshooting.
Other electronics in the garage causing RF interference?
Electronics can be anything new or old, especially phone chargers, drill/tool chargers, Fridge/freezer, motion sensors?
- Is anything plugged into the same outlet as the Garage Door Opener?
- Yes, disconnect the electronic device from power
- No, continue to step 3
- Test the remote control. Is there still a range issue?
- No, the issue was the electronic device plugged in the same outlet or the outlet itself.
- Yes, continue troubleshooting.
- Is there anything plugged in nearby?
- If so, disconnect all the items closest to the Garage Door Opener from power. Go to step 4.
- No, continue troubleshooting to step Door control step
- Test the remote control. Is there still a range issue?
- No, the issue was an electronic device plugged in nearby. (One can isolate the issue by plugging in each item, one at a time, and testing the remotes)
- Yes, continue troubleshooting
Door control wire shorted?
If there is a short or other issue in the wires to the Door Control panel, it can cause interference like any other electrical device
- Disconnect the wires from the red and white terminals. Note: Do not remove the wires that go to the safety reversing system.
- Test the remotes control. Is there still a range issue?
- No, then the issue is the door control wiring, check for loose/open connections or replace the wire completely.
- Yes: continue troubleshooting
Is there more than one Garage Door opener installed in the garage?
If there is more than one Garage Door Opener installed in your garage and only one Garage Door Opener is having an issue, the problem could be the working Garage door opener. This is known as cross-talk. To identify the issue:
- Unplug the opener which is NOT having a range issue.
- Test the remote control. Is there still a range issue?
- No, then the issue is the other Garage Door Openers logic board is sending interference, replace the logic board on the opener that you unplugged.
- Yes, continue troubleshooting
Note: Before proceeding to the next step, advise the customer that the next steps are very involved and at this point should only be completed if:
- customer insists,
- it is a pre-1998 opener (which has no other option but to be replaced)
- still experiencing issues after switching to a myQ Security+ 2.0 door control and remotes controls.
Other RF interference
If nothing else has worked and it's a pre-1998 Garage Door Opener with no other options, we have 2 more troubleshooting steps:
- Power down the garage
- Power down the home.
How to power down the garage.
- Use an extension cord to plug the opener into an outlet in the home.
- Use the circuit breaker to shut off power to the garage.
- Test range on remote controls. Is there still a range issue?
- Yes, continue troubleshooting below with Power Down Home, if the customer insists.
- No, an electronic device(s) in the garage is causing the interference. Try to identify the exact device:
- Disconnect ALL electronic devices, in the garage, from power.
- Turn the breaker back on.
- Reconnect the Garage Door Opener to its normal outlet in the garage.
- Then reconnect each electronic device to power, one at a time, and test the remote control after each reconnection to power. Do this until the electronic device causing the issue is identified. Remove or relocate electronics.
How to power down the home
- Turn off the circuit breakers to your home, except for the garage.
- Disconnect all devices in the garage from power, EXCEPT for the opener.
- Test the remote control. Is there still a range issue?
- No, If the range has notably improved, there is something in the house causing the issue. To identify what room the interference is coming from, follow these steps.
- Using the circuit breaker, restore power to one room at a time, and
- Test the remote control after each room
- Do this until you find the room that causes the remote's range to decrease.
- Yes, there is still a range issue.
Conclusion
After properly troubleshooting everything above, if the range did not improve remember the interference could be coming from a source outside of the home. These interferences can be inconsistent from one location/home to the next.
- FIOS - Fiber Optic Lines nearby (Bulletin)
- Cell Towers
- Military base
- Airports